Please Wait a Moment
X

Infor LX Tips, Infor LN Tips, BPCS Tips, Baan Tips, Infor M3 Tips & Infor ERP News

Resources Infor ERP Tips & News

Crossroads Connections

Infor ERP Tips & News from the Experts

Infor LX | Infor LN | BPCS | Baan | Infor M3

Subscribe to newsletter

Baan/LN Tip of the Week: Optionally Include Tax Amounts In Order Balance

Kathy Barthelt 0 57828 Article rating: No rating
In Baan IV, the order balance amount always includes the tax amount. Consequently, the tax amount must be recalculated every time an order line is modified in order to update the balance correctly. If the tax provider is activated, this requires an API call for every re-calculation of tax.

In Infor LN, users can select or clear the new Include Tax in Order Balance check box in the COM Parameters (tccom0000s000) session to indicate whether users want to include tax amounts in the order balance amount. This parameter has an effect on various sessions in Order Management.
Read more

BPCS/LX Tip of the Week: Shop Order Status

Anthony Etzel 0 48707 Article rating: No rating

You can see the status of the Shop Order when using SFC300 Shop Order Inquiry. You want to be sure that your shop orders are at the correct status in order to report against them.

The following are the shop order status codes:

04 = The Shop order has been entered.

05 = The Shop order has been released and printed.

14 = The Shop order has been released, but not printed. If a shop order is at this status, you have released it and it is not printed due to a system failure, or the order has been put on hold.

XX = The Shop order is closed.

Read more

BPCS/LX Tip of the Week: Work Center & Machine Locations

Anthony Etzel 0 47527 Article rating: No rating
For either file, you must specify a valid location code as defined in the Location Master File.

If the machine master locations are blank, then the work center locations are used. There are cases where you may want to do a combination between the two in defining the locations.

Let’s say the end item has one operation. The operation is at work center 510 and Machine A is in the work center. You have locations setup in both the Work center file and the Machine master File. You report 100 complete at the work center without specifying the machine.

In this case, the inventory will be processed based on the locations defined in the work center file. If the transaction included the machine number, then the locations in the machine file would be used.
Read more

Baan/LN Tip of the Week: What could go wrong with GRINYA?

Kathy Barthelt 0 59460 Article rating: No rating
One common GRINYA issue would be incorrectly entered Integration Setups.

Check the Baan/LN manual for recommended Integration setups. If such a mistake were to occur, it is important to know for what period of time the Integration was in error. It is recommended that the Integrations Setup tables be audited either through Baan or Database Auditing. Corrections can be quickly calculated when an exact timeframe can be determined.
Read more

Baan/LN Tip of the Week: Differentiating An Item By Supplier - LN

Kathy Barthelt 0 61376 Article rating: No rating

In LN, you can differentiate between items at various suppliers:

  • Locations (warehouses),
  • Purpose (planning, purchase)
  • Origin (supplier, warehouse)

Example

An item is supplied by two different suppliers. Supplier A ships in lots of 100 pieces due to how the item is packed. Supplier B ships the goods in units of 60 pieces.

You can define specific parameters for each supplier. The following sessions can be used to define these characteristics:
 
  • Items - Planning (cprpd1100m000)
  • Check Item Data by Warehouse (whwmd2210m000)
  • Item Supplier Plan (cpvmi0530m000)
These sessions define entities that have an n-to-1 relationship with the general item data.

 

Read more

BPCS/LX Tip of the Week: Inventory Control

Anthony Etzel 0 48111 Article rating: No rating

In Infor LX you need to determine how inventory will be moved in and out of warehouse storage locations, and which of the following transactions to use for inventory control:


  • A transfer transaction can be used to move inventory from one warehouse location to another warehouse location.
  • A production receipt transaction is used to add inventory to a warehouse location.
  • A material issue or backflush is used to reduce inventory from a warehouse location.
Read more

New Definition of Insanity: Collect data the same old way

Anthony Etzel 0 78661 Article rating: 5.0

Just because you've always done it this way doesn't mean it's the best way. The old way of doing things may get the job done, but is the job being performed efficiently, accurately, and on a timely basis?

People resist change because there is an element of fear behind change and having to learn something new. Sometimes it’s just that you’re comfortable with how things are done, and you don’t see the need to make any changes. 


Are you stuck in manual?

Read more

Improve Profit and Cut Costs at the Same Time

Crossroads RMC 0 34170 Article rating: No rating

Want to Improve Profit and Cut Costs at the Same Time?

“Real-time executives averaged a 14% improvement in operating cash flow and achieved a 6% reduction in operating costs” According to the Aberdeen Group.

So, how do you accomplish this great feat? By streaming real-time data to the executives.

The need for visibility into what is happening in the trenches, and the comprehensive understanding of key metrics and their implications for overall performance, are critical for an organization to be at the “top of their game”.   read full article>

Learn how Crossroads RMC can provide for this data streaming with Analytics Dashboards.

Read more
RSS
First156157158159161163164165Last

Theme picker

Tips:  LX | BPCS | M3

Did you know that you can set up one-time vendors in LX? One Time Vendor (1,A): Specify Y to indicate that this vendor is a one-time vendor. Otherwise, could you specify N. The system removes a one-time vendor's information from the Vendor Master file after all transactions are reconciled. If this vendor already exists as a one-time vendor, you can specify N to change the vendor to a regular vendor.

Read more

Determining whether to use Master Production Schedule (MPS) planning or Material Requirements Planning (MRP) planning for items in Infor LX and BPCS involves understanding the nature of the items and their demand characteristics.

Master Scheduled Items typically encompass finished goods or service items. These items receive their requirements either from Independent demand, Dependent demand, or a combination of both...

Read more
12345678910Last

Theme picker

Tips: LN | Baan

George Moroses
/ Categories: Infor, Infor ION, Upgrade & Implementation, Integrations & Enhancements, Support, Training & Workshops, Consulting, Finance, Manufacturing, Materials, Technology

Join Infor LX User Groups Open Discussion on Infor ION Basic

The Next-Generation Business Process Connectivity Software - Infor ION (Intelligent Open Network)

October 12, 2021 | 9:00am CDT
Infor ION Basic Meeting - Learn how to connect Infor LX to other systems

Please join Crossroads RMC's very own, Tim Baker, Sr. Solutions Architect, to learn how to use Infor ION to connect Infor LX to other systems, along with how to move data using Stored Procedures, API, SQL Database, and much more. 

Bring your questions and share in the open discussion!

*Register today via the LX Community calendar>

*Not a member of the Infor LX Community yet? Join today!>

Infor ION is an intelligent network that allows you to move information between systems easily without having to create point-to-point integrations. This platform loosely couples systems together so they speak the same language but are not dependent upon each other. Much like the Internet, one application can be upgraded, replaced, or even fail without taking down the entire network. Built using non-proprietary standards, Infor ION provides an open architecture that is flexible, scalable, and adaptable.

Learn more about Infor ION on Crossroads RMC's website>

---------------------------------------------------------------------

*ACCOUNT ACTION REQUIRED - PLEASE NOTE: The LX User Group has moved to https://concierge.infor.com. Please confirm you have access ASAP. All access requests require approval by your organization's support admin, so please sign in to confirm access, or sign up now, or reach out to your organization's support admin to ask them to add you.

Once you have access to https://concierge.infor.com, click on the Communities box, and join the LX - User Group - LX. You'll find this meeting on the calendar.

----------------------------------------------------------------------

More ways to join the meeting on October 12th:

Join from the meeting link:
https://formica.webex.com/formica/j.php?MTID=m9fb912c4927f947a034247aefc1cd94b

Join by meeting number: 
Meeting number (access code): 2311 777 6157
Meeting password: pWJFmmRX522

Tap to join from a mobile device (attendees only):
+1-646-992-2010,,23117776157## United States Toll (New York City)
+44-20-3198-8143,,23117776157## United Kingdom Toll

Join by phone:
+1-646-992-2010 United States Toll (New York City):
+44-20-3198-8143 United Kingdom Toll
Global call-in numbers | Toll-free calling restrictions

Join from a video system or application:
Dial 23117776157@formica.webex.com
You can also dial 173.243.2.68 and enter your meeting number

Print
15444 Rate this article:
5.0
George Moroses

George MorosesGeorge Moroses

Other posts by George Moroses
Contact author

Theme picker

Contact author

x

Categories